钢制导热油烘缸的数值模拟与结构优化

针对钢制导热油烘缸在工作时出现工作表面温度分布不均匀、温差大等情况，采用三维建模和模拟仿真方法对钢制导热油烘缸的结构进行优化。本研究主要从3个方面对钢制导热油烘缸进行结构改进，分别是改变循环油路通道数量，改变进油槽与出油槽上孔的排列方式，改变循环油路的结构。研究结果表明，相对其他烘缸结构，具有循环油路通道数量为20个、进油槽与出油槽上孔为单排排列、循环油路两两相通的钢制导热油烘缸的性能更好，可以达到工作表面温度分布均匀、温差控制在±5℃以内的目的。     

高层建筑中上下相邻双层大跨度钢桁架施工技术

介绍了上海前滩10-01地块(办公及住宅)高层建筑上下相邻双层大跨度钢桁架施工技术。结合项目桁架结构特点,分析讨论了双层桁架的支撑措施布设及安装过程中的注意要点,解决了±0m楼板不能满足双层桁架荷载要求的问题,提出了待下层桁架支撑卸载后,利用下层桁架布设上层桁架支撑,完成上层桁架安装的方案。同时通过有限元计算分析,对桁架施工过程进行计算模拟,研究施工过程的结构位形及内力,保证施工质量与安全。     

Advances in the in vitro digestion and fermentation of polysaccharides

In vitro digestion models are widely used to study the structural changes, digestion and release of food components under simulated gastrointestinal conditions. As compared to the in vivo digestion tests, the in vitro digestion reflects the digestion and utilisation of food after ingestion and has the advantages of being time consuming, inexpensive, reproducible and free from moral and ethical restrictions. This study reviewed the current research studies on the in vitro simulated digestion of polysaccharides conducted in the last 5 years and focused on the oral, gastric and intestinal digestion models, with the aim of providing a basis for the further testing of changes in the content, structure and active ingredients of polysaccharides before and after digestion.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Pore-scale study of effects of different Pt loading reduction schemes on reactive transport processes in catalyst layers of proton exchange membrane fuel cells

Reducing the Platinum (Pt) loading while maintaining the performance is highly desired for promoting the commercial use of proton exchange membrane fuel cells (PEMFCs). Different methods have been adopted to fabricate catalyst layers (CLs) with low Pt loading, including utilizing lower Pt/C catalysts (MA), mixing high Pt/C catalysts with bare carbon black particles (MB), and reducing CL thickness while maintaining high Pt/C ratio (MC). In this study, self-developed pore-scale model is adopted to investigate the performance of the three Pt reduction methods. It is found that MA shows the best performance while MB shows the worst. Then, effects of Pt dispersion are further explored. The results show that denser Pt sites will result in higher local oxygen flux and thus higher local transport resistance. Therefore, MA method, which shows the better Pt dispersion, leads to improved performance. Third, CLs with quasi-realistic structures are investigated. Higher tortuosity resulting from the random pores produces higher bulk resistance along the thickness direction, while MA still exhibits the best performance. Finally, improved CL structures are investigated by designing perforated CL structures. It is found that adding perforations can significantly reduce the bulk transport resistance and can improve the CL performance. It is demonstrated that CL structure plays important roles on performance, and there are still huge potentials to further improve CL performance by increasing Pt dispersion and optimizing CL structures.     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

面向草莓抓取的气动四叶片软体抓手研制

农林业中果蔬的自动化采摘需求日趋强烈,末端抓手是实现无损采摘的关键。传统的末端抓手以刚性结构居多,现有的各种柔性抓手也存在抓取力不足、包覆性不佳等缺点。本文以草莓的无损采摘为研究对象,提出将草莓外部轮廓曲线作为设计曲线,设计了一种新型气动四叶片软体抓手。首先,对软体抓手的结构做仿真优化,提出一种安全地附着在目标物表面的设想。然后,在进行草莓表面的最小破坏应力试验的基础上,测试了软体抓手的末端力,验证了其实现无损抓取的可行性。再次,利用动态捕捉技术,研究了软体抓手叶面的弯曲变形规律。最后,选择使用弧线型气体通道的软体抓手进行了草莓抓取测试,结果证明了气动四叶片软体抓手可以实现草莓的无损抓取,抓取成功率达90%,破损率为2%,表明所研制的四叶片软体抓手用于草莓抓取时具有良好的稳定性和实用性,可用于草莓采摘的末端执行器。本研究也可为其他易损果蔬的采摘技术提供理论基础和技术支撑。     

基于GIS单线图的配网停电单模拟操作应用研究

配电网停电会造成电力系统供配电可靠性以及服务质量下降,研究基于地理信息系统(GIS)单线图的配网停电单模拟操作应用。利用网格长度作为基本单位建立坐标系,以选取起始点与终止点为基础,通过四参数法将GIS坐标映射至图纸网格内,实现配网内设备初步布局,将杆塔、站房和整体均匀分布作为优化目标,设置多目标优化目标函数实现GIS单线图最终优化。选取某电力公司配网作为单模拟操作应用对象,模拟结果表明,单模拟操作配网停电后,该配网各负荷点年故障率、次平均停电时间以及年停电时间均有所减少,可有效提升配网的供配电可靠性。     

射频电缆的幅相稳定性测试研究

对射频电缆幅相稳定性进行了介绍,阐述了射频测试电缆相位和幅度变化的因素,并详细分析了射频电缆相位性能以及幅度性能的不同测试方法,最后通过实测数据的展示,总结说明了在日常测试中该如何正确使用测试电缆。     

非全日制研究生线上线下混合式教学模式研究 ——以《现代电气控制技术》为例

随着教育信息化技术的发展，线上线下混合式教学模式已成为一种趋势。为了解决非全日制研究生课堂教学召集困难、效果不佳等问题，提出了基于“互联网＋虚拟仿真技术”的线上线下混合式教学模式。本文以控制工程专业学位研究生为例，结合《现代电气控制技术》课程，探讨了线上线下混合式教学实现途径、师生互动方法、项目驱动案例教学法以及电气控制系统虚拟仿真实验平台的构建方法，切实提升非全日制研究生的培养质量。